HVAC & Generators in Shelbyville, KY

Completed water heater replacement by draining and removing the existing tank from the residential utility room. Installed a new AC Smith ProLine 50-gallon short water heater utilizing the original shut-off valve and existing plumbing connections. Installed a new temperature and pressure relief valve with discharge pipe properly terminated to within 6 inches of the floor per code requirements. Reconnected copper supply lines with brass fittings and verified proper gas line connection to the control valve. Unit tested and confirmed operational with no leaks detected at connections.

Responded to no hot water complaint affecting entire residence. Upon arrival, inspected gas water heater located in basement utility area. Diagnosed pilot light failure preventing burner ignition. Verified gas supply to unit, checked thermocouple functionality, and cleared pilot assembly of debris. Successfully relit pilot light, confirmed proper flame characteristics, and tested burner operation through full heating cycle. Verified hot water restoration at fixtures throughout home and ensured all safety controls functioning properly before departing.

Installed a 40-gallon State ProLine Commercial Grade electric water heater in utility closet. Connected hot and cold water supply lines using PEX piping with brass fittings, installed pressure relief valve with discharge pipe, and verified all connections for proper operation and code compliance.

Responded to service call for malfunctioning thermostat on 6-year-old heat pump system that would not shut off, causing temperature discrepancy between actual (68°F) and setpoint (71°F). Upon inspection, assessed existing Whirlpool water heater (Model MHE2F40RS035V) showing signs of age and determined replacement was necessary. Provided on-site estimate for new water heater installation and obtained approval for equipment upgrade to resolve household hot water needs.

Responded to service call for 6-year-old heat pump system that would not shut off. Diagnosed malfunctioning Honeywell wireless thermostat causing continuous system operation despite reaching setpoint. Removed defective wireless thermostat and installed new Honeywell wireless thermostat kit at air handler location. Verified proper system cycling, confirmed unit now responds correctly to temperature calls and shuts off at setpoint. System tested and operating within normal parameters.

Responded to service call for multiple electrical issues including non-functioning garage lighting, loose or inoperative outlets, and a failing bathroom exhaust fan. Inspected exterior weatherproof outlet mounted on vinyl siding and evaluated ceiling-mounted bathroom ventilation fixture with integrated lighting. Diagnosed electrical connectivity problems at receptacle locations and assessed ventilation fan motor performance to determine repair requirements.

# HVAC Maintenance Report Completed comprehensive AC tune-up on 6-year-old air conditioning system. Performed full system inspection revealing significant dust and debris accumulation on blower wheel assembly and outdoor condenser coil requiring thorough cleaning. Cleaned blower wheel fins and housing, removing accumulated dust and particulate matter to restore optimal airflow. Cleaned outdoor condenser coil mesh, removing heavy buildup of dirt, dust, and fibrous debris that had clogged the unit and restricted heat transfer efficiency. Inspected all electrical connections, tested capacitor values, verified refrigerant pressures, and confirmed proper system operation. All mechanical components functioning within normal parameters. System operating efficiently following maintenance service with improved airflow and heat exchange capabilities.

Responded to service call for exterior electrical installation on outbuilding. Inspected weatherproof electrical boxes and conduit system mounted to wooden post structure on white corrugated metal building. Documented existing three-box configuration with gray flexible conduit connections running between junction boxes and to ground level, verifying proper outdoor-rated components and secure mounting to pressure-treated lumber support.

Responded to service call for pool pump switch estimate. Upon arrival, inspected existing outdoor electrical installation consisting of multiple junction boxes and disconnect mounted on exterior wall with associated conduit runs. Documented current configuration of electrical service setup including open disconnect box revealing internal wiring connections with multiple circuit conductors. Provided estimate for installation of flip switch control for pool pump operation based on existing electrical infrastructure and equipment accessibility.

Performed comprehensive plumbing inspection at a 21-year-old residential property to diagnose a non-functioning garbage disposal and leaking kitchen faucet. Conducted visual assessment of the InSinkErator-style disposal unit mounted beneath the kitchen sink, examining electrical connections, reset button, mounting assembly, and discharge plumbing. Inspected the flexible corrugated drain line connection and verified proper alignment with the waste line system. Evaluated the brushed nickel kitchen faucet for leak source, checking supply line connections, cartridge integrity, O-rings, and aerator assembly. Documented existing plumbing configuration including white PVC drain system and under-sink cabinet conditions through photographic evidence. Provided detailed findings and repair recommendations to address both the inoperative disposal unit and the persistent faucet leak that had been occurring for approximately two weeks.

Responded to a main drain backup causing sump pump bubbling and water accumulation in the basement. Located the main cleanout approximately 10 feet from the affected area on the exterior wall and performed a complete drain cleanout to restore proper flow to the municipal sewer system. Successfully cleared the blockage, eliminating the backup condition and restoring normal drainage function throughout the system.

Performed routine maintenance flush on Whirlpool tanked water heater previously installed in basement utility area. Drained sediment buildup from tank bottom through drain valve, inspected temperature and pressure relief valve discharge piping, and verified all connections and access panels were properly secured. Unit returned to normal operation with improved efficiency.

Responded to service call for RainSoft water softener system emitting strong odor. Upon arrival, inspected dual-tank water treatment system and brine tank. Removed contaminated salt from brine tank, which showed significant sediment and debris buildup at bottom causing malodorous conditions. Cleaned and sanitized brine tank interior, removing accumulated residue and organic matter. Refilled system with fresh water softener salt and verified proper operation of digital control head. Tested system cycling and confirmed elimination of odor issue. System restored to normal operating condition.

Completed follow-up site visit for Lennox heat pump installation. Refrigerant lines and electrical conduit require line hide installation to soffit, and damaged Armaflex insulation in knee wall needs foam taping to complete weatherization. Documentation photos captured of exterior unit positioning and line routing for completion scheduling.

Installed new ball valve on water heater system and removed existing expansion tank from wall-mounted plumbing configuration. Work performed on copper piping junction with multiple connection points, addressing water leak concerns. Expansion tank reinstallation scheduled for following day to complete system pressure regulation repair.

Responded to water leak reported above water heater in utility closet. Upon inspection, identified failed expansion tank with active leak at connection point on vertical copper supply line. Existing 2-gallon expansion tank showed significant corrosion and deterioration at threaded connection, causing water discharge onto surrounding piping and drain pan. Documented condition of corroded copper piping throughout assembly and noted multiple aged connections with heavy patina buildup. Ordered replacement 2-gallon expansion tank with female 3/4" pro press copper adapter for installation. System remains operational with water supply active. Scheduled follow-up installation appointment for next day upon part delivery. Estimated repair time of 45 minutes for tank replacement and connection. Advised customer of repair plan and timeline for completion.

Completed dismissed visit maintenance on a two-year-old single-system HVAC unit. Replaced 20x20x5 pleated air filter and performed system inspection of Lennox outdoor condenser unit. Documented equipment condition with photos and collected renewal payment for continued service coverage.

Conducted follow-up site inspection to document incomplete work items from previous HVAC installation. Photographed exterior condenser location showing drainage concerns and vegetation growth around foundation, as well as interior attic laundry area where ductwork and ventilation components require completion. Documented current conditions for scheduling final installation phases.

Responded to a no-power issue affecting an electrical circuit running to a detached shed. Upon inspection, located a faulty junction box with compromised wiring connections in the overhead space between the main structure and shed. Replaced the damaged junction box, re-terminated all wire connections to code, and restored full power to the shed circuit.

Responded to water leak service call and performed comprehensive plumbing inspection of bathroom fixtures. Identified issue with toilet supply line connection and assessed condition of bathtub drainage system. Presented repair options to customer and successfully sold necessary repairs to resolve the water leak and prevent future plumbing issues.