Heating, Cooling & Indoor Air Quality in Boonville, IN

Completed scheduled maintenance tune-up on a 2-year-old Lennox heat pump system currently operating properly. Performed comprehensive inspection of electrical control components including transformer, contactors, relays, and main control board PCB with all connections verified secure. Inspected heat exchanger coil assembly, serpentine refrigerant lines, and evaporator coil noting minor surface discoloration consistent with normal operation; all components functioning within manufacturer specifications with system confirmed operational upon completion.

Completed routine planned maintenance on residential air conditioning system installed in 2020. Performed comprehensive AC tune-up including electrical diagnostics, measuring voltage at 385V using calibrated multimeter to verify proper power supply to system components. Inspected evaporator coil assembly, noting significant oxidation and patina on copper tubing consistent with system age and normal moisture exposure. Observed dust and debris accumulation on aluminum cooling fins. Verified refrigerant line connections and brass valve fittings for proper sealing. Checked condensate drain system including PVC piping for proper drainage. All electrical connections tested and found operational. System operating within normal parameters upon completion of maintenance service.

Successfully installed a 12,000 BTU Lennox ductless mini-split system with indoor wall-mounted evaporator unit. The installation was completed professionally with proper mounting, refrigerant line connections, condensate drainage, and electrical wiring, resulting in a fully operational system displaying 62°F on the digital control panel.

# HVAC Install - Complete System Completed Day 2 of full system installation featuring a 3-ton Lennox EL18XC1CV-036-230B04 air conditioning condenser with 18 SEER efficiency rating paired with an 80% AFUE upflow gas furnace with fully modulating capabilities. The outdoor condenser unit was positioned on ground-level pad with proper clearances and secured connections. In the attic space, installed the air handler unit on wooden platform with appropriate structural support and connected flexible aluminum ductwork routing to existing distribution system. Ran electrical wiring from air handler to power source following code requirements. Installed fiberglass insulation around ductwork connections to maximize system efficiency. Verified all electrical connections at single-phase 230V power supply with proper amperage ratings per manufacturer specifications. System commissioning included verifying proper refrigerant charge, airflow measurements, and testing modulating furnace operation acro

Completed planned maintenance visit on 12-year-old single-system residential HVAC installation consisting of Carrier furnace with integrated humidifier and matching outdoor condensing unit. Performed comprehensive system inspection including visual assessment of indoor equipment installation, ductwork connections, and exterior condenser unit condition. All equipment operational with no immediate service concerns identified during this second follow-up maintenance visit.

Completed annual planned maintenance on 11-year-old HVAC system located in utility closet. Performed standard maintenance procedures including system inspection, filter replacement with 20x20x1 filters, and operational testing of furnace unit. Delivered additional filters as requested and documented equipment condition with photographs showing unit, PVC ventilation piping, and access panels in satisfactory working order.

Completed comprehensive Platinum Level planned maintenance on dual HVAC system consisting of two 1-year-old units. Performed thorough inspection of three outdoor condensing units located on exterior gravel pad area, checking refrigerant lines, electrical connections, and verifying proper operation of all components. Inspected indoor equipment including furnace units, ductwork, and plenum assemblies. Replaced two 16x25x5 air filters as part of routine maintenance protocol. Verified all PVC condensate drainage, tested safety controls, and confirmed proper airflow throughout both systems. All equipment operating within manufacturer specifications with no issues identified.

Conducted comprehensive site evaluation for mini-split system installation at residential property. Assessed exterior and interior mounting locations, documented existing building structure including wood siding and brick exterior, evaluated electrical access points, and photographed proposed equipment placement areas to develop accurate system sizing and installation quote.

Completed planned maintenance on a 3-year-old HVAC system during second scheduled visit. Serviced outdoor condenser unit, replaced 20x25x5 air filter, and performed standard system inspection to ensure optimal performance and efficiency.

Completed routine planned maintenance on air conditioning system. Performed comprehensive inspection of evaporator coil assembly, noting significant oxidation on copper coil surfaces and refrigerant lines consistent with system age and normal operation. All internal components inspected and found operational, with heat exchanger and ventilation elements showing standard wear patterns. System tested and confirmed functioning within normal parameters.

Conducted on-site evaluation for complete HVAC system replacement at residential property. Documented existing outdoor equipment configuration, including current piping layout, plumbing connections, and available workspace for new system installation. Captured detailed photographs of installation area to provide accurate assessment for equipment specifications, required modifications to existing infrastructure, and comprehensive replacement quote preparation.

Responded to no cooling call on approximately 20-year-old space pak system that was unable to maintain temperature setpoint, with thermostat set to 78°F but indoor temperature reading 85°F. Upon inspection, found aging high-velocity HVAC system installed in attic space showing signs of significant wear and decreased capacity. System evaluation revealed unit was operating but struggling to achieve adequate cooling output due to age-related degradation. Documented existing equipment condition including heavily insulated refrigerant lines and attic-mounted air handler configuration typical of space pak installations. Discussed system performance limitations with homeowner and provided options for improving comfort, including repair versus replacement considerations given the advanced age of the equipment and diminishing efficiency.

Responded to no cooling complaint on 3-4 year old outdoor combination unit that had never been operated in cooling mode. Upon arrival, confirmed reduced airflow and blower motor operating at diminished capacity. Diagnosed system requiring thorough cleaning due to extended period of non-use and accumulated debris affecting airflow and cooling performance. Documented interior ventilation components and system conditions with photos for service records.

Responded to no cooling complaint on 10-year-old system with inadequate airflow to upstairs bedroom vents and elevated temperatures reaching 85°F. Investigated ductwork serving affected zones and discovered supply duct disconnection at plenum connection point in attic space. Reconnected and sealed ductwork using mastic, restoring proper airflow to all upstairs registers and resolving temperature imbalance between floors.

Completed second annual Gold Level planned maintenance on 7-year-old residential HVAC system. Performed comprehensive inspection of air handler unit with front panel removed to access internal components including evaporator coil, heat exchanger, and electrical connections. Verified proper operation of all wiring harnesses and checked condition of coils for debris or damage. Inspected PVC condensate drain lines for proper flow and connections. Examined insulated ductwork and verified secure attachment points. Replaced 20x25x5 media filter per maintenance protocol. Checked condensate pump operation and verified proper drainage. All components found operating within normal parameters and system performing as expected.

Completed installation of 3-ton, 14.7 SEER Lennox air conditioning system with matching evaporator coil in side yard location. Unit was properly positioned on concrete pad with adequate clearance, refrigerant lines were connected and charged to manufacturer specifications as verified by manifold gauge readings, and system was tested for proper operation with pressures stabilized at 439 PSIG high side and 310.8 PSIG low side with corresponding temperatures confirming correct refrigerant charge.

Completed annual planned maintenance on 1-year-old residential HVAC system during second visit. Performed comprehensive inspection of furnace and associated components, verified proper operation of blower motor assembly, and inspected all electrical connections and controls. Replaced 16x25x5 air filter per maintenance schedule. Inspected condensate drain lines, PVC venting system, and flexible ductwork for proper installation and function. All equipment operating within normal parameters with no deficiencies noted.

Responded to no cooling call on 20-year-old system with complete loss of airflow. Upon arrival, verified Lennox Signature Stat thermostat had power and display was functioning properly. Performed diagnostic evaluation of HVAC system to determine cause of no air handler operation and identified failure requiring system replacement due to age and condition of equipment.

Completed Platinum Level maintenance on a 6-year-old single HVAC system. Replaced 20x25x5 furnace filter, inspected outdoor condensing unit positioned on concrete pad against building exterior, and verified proper system operation. All components found in good working condition with no issues identified during inspection.

Conducted comprehensive replacement estimate for 23-year-old residential HVAC system. Evaluated existing outdoor condensing unit located in side yard between house and wooden fence, noting unit positioned on concrete pad with adequate clearance. Assessed current system configuration including downflow air handler setup with existing furnace, evaporator coil, and base components. Documented equipment dimensions and spatial constraints for replacement planning, including 40-foot refrigerant line set routing from outdoor unit to indoor air handling equipment. Photographed existing installation conditions and created technical schematic showing proposed vertical equipment configuration with color-coded component layout. Provided homeowner with detailed replacement options and specifications for new system installation to address aging equipment concerns.