HVAC & Generators in Shepherdsville, KY

Completed Platinum Level maintenance on a single HVAC system during the first visit of an 8-year service agreement. Replaced 16x25x5 air filter, performed comprehensive system diagnostics using digital measuring instruments to verify temperature differentials and electrical parameters, and confirmed all components operating within manufacturer specifications.

Completed Platinum Level maintenance on a 7-year-old HVAC system, including replacement of the 16x20x5 air filter as recommended from the previous visit. Performed comprehensive system diagnostics using digital multimeter, verifying electrical readings and system performance parameters to ensure optimal operation.

Conducted comprehensive HVAC replacement estimate for residential system with 7-year-old cooling unit running constantly and heating system approximately 15+ years old. Evaluated existing electrical panel configuration, circuit breaker setup, and ductwork condition to determine full system replacement requirements including air duct work modifications. Documented existing equipment specifications, electrical infrastructure, and mechanical components to provide complete replacement proposal for both heating and cooling systems.

Completed scheduled HVAC maintenance on Lennox system unit. Performed comprehensive tune-up inspection, verified refrigerant line connections, checked electrical connections, and confirmed proper system operation with no issues identified.

Completed second annual planned maintenance visit on 8-year-old HVAC system. Performed comprehensive system diagnostics on outdoor condensing unit, including electrical testing with multimeter to verify proper voltage and amperage readings. Measured supply voltage at 386V and confirmed compressor amp draw at 8.5A, both within manufacturer specifications. Inspected condenser fan motor operation and blade condition through protective grille. Verified all electrical connections and terminals for proper contact and absence of corrosion. System operating efficiently with all parameters normal. Recommend filter replacement with 16x25x5 filter per maintenance schedule and renewal of annual maintenance agreement for continued system protection.

Completed diagnostic inspection on 1-year-old HVAC system with reported operational concerns. Accessed crawlspace to inspect flexible ductwork installation and support strapping. Verified floor register placement and airflow distribution to living space. Documented existing conditions of insulated supply duct routing and structural support components. System confirmed operational at time of service with repair parts ordered and ready for installation upon arrival.

Conducted follow-up site visit to inspect mini-split system and verify replacement parts prior to scheduled installation. Photographed equipment specifications and model information on new mini-split indoor heads, confirmed part numbers match work order requirements. Utilized refrigerant manifold gauge set to assess system operating parameters and document baseline readings for upcoming replacement of all indoor heads and outdoor condensing unit.

Responded to service call for 1-year-old Navien tankless water heater displaying error code 003 with no hot water production. Performed diagnostic evaluation of unit with front cover removed to access internal components. Inspected heat exchanger assembly, circuit boards, electrical controls, and all associated plumbing connections including hot and cold water lines and gas supply line. Identified and resolved error code issue, restoring full hot water functionality to the system.

Completed comprehensive HVAC system replacement estimate for existing air handler and evaporator coil assembly located in attic space. Assessed current system configuration including foil-faced insulated air handler unit, copper refrigerant line set, PVC condensate drain line, and existing ductwork with reflective insulation. Documented equipment dimensions and spatial constraints for replacement unit sizing. Evaluated attic access, clearances, and installation requirements for new system components. Provided homeowner with detailed replacement options and specifications for complete system upgrade.

Completed installation of 40-gallon gas slim water heater in residential utility closet. Connected copper water supply lines with brass shut-off valves, attached flexible yellow gas line to unit, and verified proper venting through existing galvanized vent pipe extending through ceiling. Installation includes 6-year manufacturer warranty on parts and 1-year labor warranty.

Responded to emergency call for water heater failure and conducted on-site estimate for 32-gallon gas tank water heater replacement. Assessed existing plumbing configuration including copper supply lines with shut-off valves and evaluated installation requirements in utility room area. Provided homeowner with replacement options and specifications for new tank-style gas water heater system.

Completed warranty follow-up visit to finalize previous water heater installation after electrical power was restored to the system. Previously installed 50-gallon electric water heater with new ball valves and replaced shallow well water pump with pressure tank and copper piping connections. Return visit scheduled to replace 5 shut-off valves, perform minor reciprocating work on shut-offs, and relocate shower head to new position per specifications.

Conducted comprehensive HVAC system evaluation for non-functional air conditioning unit in recently purchased residential property. Assessed existing outdoor condensing unit located in narrow utility area alongside gas lines, electrical conduits, and plumbing infrastructure, noting equipment condition and accessibility constraints. Inspected basement-installed furnace system with vertical venting configuration, evaluated existing ductwork, and documented current equipment specifications. Provided complete replacement estimate options and discussed available financing solutions for full HVAC system installation.

Completed planned maintenance visit on residential single-system HVAC unit with focus on cooling system components. Performed comprehensive inspection of outdoor condenser unit, verified proper operation of fan assembly and compressor, checked refrigerant levels, and cleaned condenser coils. Inspected thermostat operation showing system set to 72°F in cooling mode with auto fan setting, confirmed accurate temperature readings and proper communication between thermostat and equipment. Documented system condition with photos showing outdoor unit in good operational condition with no visible damage or wear, proper drainage around gravel pad, and secure electrical connections. All cooling system components functioning within normal parameters for 4-year-old equipment using 16x25x1 filter size.

Installed new 1/2 HP well pump system with diaphragm expansion tank and pressure gauge in basement utility area, running new water lines and making all necessary connections to the existing plumbing system. Installed 50-gallon A.O. Smith electric short water heater with copper supply lines and red shut-off valve assembly. All equipment mounted securely on concrete floor with proper clearances, pressure monitoring capabilities in place, and system tested for proper operation upon completion.

Completed follow-up visit to discuss maintenance plan options and advised of Platinum Plan benefits, including extended labor warranty coverage for the new system. Delivered and provided 16x26x5 Pure Aire filter kit at no charge as previously arranged. Documented visit with photos of equipment location.

Responded to service call for water heater and well pump inspection following previous flood damage that resulted in 8 feet of water in the home. Upon arrival, conducted thorough assessment of existing U.S. Craftmaster water heater with 6.75M capacity, which exhibited significant deterioration including extensive rust staining, discoloration, and visible wear throughout the tank exterior, particularly concentrated on the lower third of the unit. Inspected well pump system including blue pressurized expansion tank mounted on metal frame platform and horizontal circulation pump with associated piping connections. Documented condition of all equipment with photographs showing compromised water heater condition likely resulting from flood exposure. Evaluated pressure tank, pump assembly, copper piping, valves, and electrical connections for proper operation and signs of water damage. Provided customer with assessment findings regarding water heater condition and recommendations for replace

Completed installation of I-Wave air purification system on existing Bryant HVAC unit and added two new supply registers to the ductwork system. All components were properly mounted, sealed with foam insulation at connection points, and tested for proper operation to enhance indoor air quality.

Responded to no cooling call on 7-year-old residential air conditioning system. Upon arrival, verified thermostat was calling for cooling with display showing 78°F actual temperature and 75°F setpoint. Proceeded to outdoor condensing unit to perform diagnostic testing. Using digital multimeter, tested electrical components and identified failed dual-run capacitor with reading of 438 volts during system operation. Replaced defective capacitor with manufacturer-specified replacement unit. Cycled system through complete operational test, confirmed proper voltage readings, verified compressor and condenser fan motor startup, and restored full cooling functionality to the system.

Conducted comprehensive indoor air quality assessment and HVAC system evaluation for residential property. Documented existing Bryant air handler installation in utility closet, including flexible ductwork connections, refrigerant line routing, and electrical conduit placement. Photographed secondary HVAC system featuring stacked configuration with furnace/air handler base unit and evaporator coil assembly, noting insulated ductwork connections and proper refrigerant line installation. Prepared detailed estimate for indoor air quality improvements based on current system conditions and customer requirements.